Accessories and cables
PAX S300 and S80 setup: power cable, Ethernet and Wi-Fi questions
Connect a PAX S300 PIN pad or S80 countertop terminal: the S300 power cable dongle, Ethernet to the router, why there is no Wi-Fi, and fixing Check LAN Cable.
- Applies to
- PAX S300, S80 · S300-000-363-01NA, S300-000-364-02NA
- Last reviewed
- Oct 27, 2026 by Abdul Rashid
Exact messages this covers
Check LAN CableTerminal Locked
Check first
- Which model is it, and for an S300, which part number is on the serial label on the back (363-01NA or 364-02NA)?
- Is the network cable plugged into a router, or into a network switch?
- Does the cable end show 8 copper contacts (Ethernet) or 4 (phone cord)?
The PAX S300 PIN pad and S80 countertop terminal connect by Ethernet cable to your router. Neither has Wi-Fi, according to PAX's own connection table. The S300 gets power and its connections through a cable dongle that plugs into a 14-pin socket under the SAM cover on the back, and it turns on as soon as power is connected.
Before you start
- Check the S300 box: PIN pad, power supply, power adapter and stylus pen.
- Use a real Ethernet cable. The plug end has 8 copper contacts; a phone cord has 4.
- Plug into the router if you can. A plain network switch does not hand out IP addresses.
- If Allstar programmed the terminal, leave the payment application settings alone.
Steps
- S300 only: take off the SAM cover on the back. On part number 363-01NA press the finger pad and push the cover up; on 364-02NA remove the top screw and lift the cover. Expected: the 14-pin socket and dongle connector are visible.
- S300 only: check the pins are straight and clean, push the connector straight down into the socket, and refit the cover. To unplug it, grip the sides and pull straight up. Expected: the connector is firm. Bent or loose pins can cause Check LAN Cable.
- Run an Ethernet cable from the terminal's LAN port (on the S300, through its power cable) to a free router port. Expected: a link light on the router port.
- Plug in the power adapter. The S300 has no power button: it turns on with power and off when unplugged. Expected: the terminal boots to its idle screen.
- If you see Check LAN Cable, reseat both ends, check the router light, try another port, then swap in a known-good Cat 5e or Cat 6 cable. On an S300 also reseat the dongle (steps 1 and 2). Expected: the message clears.
- DHCP errors on a switch: move the cable to the router, or get a static IP address from your network administrator and contact support to enter it. Expected: the terminal gets an address and connects.
If that did not work
The S80 and S300 have no Wi-Fi, so there is no wireless setting to find; if you need wireless, ask Allstar about an Android model. A Terminal Locked screen means the password was entered wrong too many times: power cycle once and get the correct password from your ISO or Allstar. Firmware messages (Warning App Exception, Error Lookup Firmware Entry) are handled with PAX and your processor on the phone, so contact support. Any tamper or security message: stop, do not reboot repeatedly, contact support.
Contact Allstar support with the model, serial number, payment application, processor and the exact message on screen.
Sources
- S300 Quick Setup Guide (no version printed)
- PAX Technical Knowledge Base: S300 Power Cable Adaptor Connection (dated 12.5.2018)
- PAX Technical Knowledge Base: Check LAN Cable (updated 2026-08-26)
- PAX Technical Knowledge Base: Connection Type in Every Terminal (updated 2026-08-26)
- PAX Technical Knowledge Base: S80 General Information (updated 2026-08-26)
- PAX Technical Knowledge Base: General Information for Traditional Terminals (updated 2026-08-26)
- PAX Technical Knowledge Base: Terminal Locked (updated 2026-08-26)
Stop and contact support if
- Wi-Fi: PAX lists the S80 and S300 as Ethernet (LAN) and dial-up only, with no Wi-Fi. If you need wireless, ask Allstar about an Android model instead of trying to configure Wi-Fi.
- S300 connector pins damaged or missing: do not force it. The unit needs repair; contact Allstar support.
- Terminal Locked on screen: the password was entered wrong too many times. Power the terminal off and on once, then contact your ISO or Allstar for the correct password. Passwords are not given here.
- Warning App Exception, Error Lookup Firmware Entry or any firmware message: stop. Firmware updates are done with PAX and your processor on the phone. Contact Allstar support.
- Any 'PED Tampered' or other tamper or security message: stop, do not reboot repeatedly, contact support.
Contact Allstar support (support@allstarterminals.com, 888-403-7066, Monday to Friday 9 AM to 5 PM Central) with the model, serial number, payment application, processor and the exact message on screen.
Notes
- pax.us publishes an S300 quick setup guide (no version or date printed) but none for the S80. The S300 guide covers box contents, SAM card, power and card reading only; it has no cabling steps.
- The S300 power cable article is dated 12.5.2018 in its body. PAX links bent pins in the 14-pin connector to Check LAN Cable, which suggests the network connection runs through the power cable dongle; PAX does not say this outright (unverified, inference).
- No PAX page describes the S80's ports or how to power it on and off. S80 steps here come from PAX's S80 and traditional-terminal FAQs (Ethernet to router, not phone cord; DHCP on a switch). PAX marks the S80 as end of life and says repair may not be available.
- PAX's connection table lists S80: LAN and dial; S300: LAN and dial (dial only with an EM100 unit PAX no longer makes). No Wi-Fi on either. Older or regional variants are not covered.
- Static IP entry on these terminals is a menu inside the payment application behind the terminal password; it is routed to support rather than printed.
- PAX says traditional terminals reboot 24 hours after power-on as a PCI requirement. Unplugging and replugging at the time you want moves the reboot.
Sources
- S300 Quick Setup Guide · read 2026-10-26 · manufacturer documentation
- PAX Technical Knowledge Base: S300 Power Cable Adaptor Connection · 2018-12-05 · read 2026-10-26 · manufacturer documentation
- PAX Technical Knowledge Base: Check LAN Cable · 2026-08-26 · read 2026-10-26 · manufacturer documentation
- PAX Technical Knowledge Base: Connection Type in Every Terminal · 2026-08-26 · read 2026-10-26 · manufacturer documentation
- PAX Technical Knowledge Base: S80 General Information · 2026-08-26 · read 2026-10-26 · manufacturer documentation
- PAX Technical Knowledge Base: General Information for Traditional Terminals · 2026-08-26 · read 2026-10-26 · manufacturer documentation
- PAX Technical Knowledge Base: Terminal Locked · 2026-08-26 · read 2026-10-26 · manufacturer documentation
Was this guide helpful?
Thanks. The team reviews this feedback.
